C&K systems System 238 Manuale di Installazione Scaricare il pdf (Pagina 2)

SYSTEM 238 Installation Manual

Subject Page No.

System 238 Terminal Label Front Cover

Residential and Commercial Installation Guidelines 2

Installation 2 - 3

Wiring the Panel 3 - 4

System Start-Up 4

Keypad Setup 4 - 5

Addressing Keypads 5

Factory Default Settings 5

Programming Options (Alphabetical List) 5 - 6

Programming the Panel 6

Programming with the LED Keypad 6

Programming with the Alpha Keypad 6

Entering Hexadecimal Numbers 6

Programming the Alpha Keypad 6 - 7

Programming Letters & Numbers 7

Special Function Keys 7

Programming Options (Numerical Order) 8 - 18

Keypad Label Drawer 19

Telephone Line Problems 19

Watchdog Indicator 19

Keypad Operation Command Summary 20

Help with Common Problems (Troubleshooting) 21 - 22

Reducing False Alarms 23 - 24

Programming Worksheets 26 - 27

Table of Contents

Scope of This Manual

This manual contains basic installation and programming information

for the SYSTEM 238. For additional information about using or

programming the system, please refer to the SYSTEM 238 Keypad

Manual, Alpha Keypad Manual, or Commander II/Monitor II Operating

Manual.

BEFORE YOU START

12. The system must not be programmed to dial a police

station.

13. Use screws (supplied) to secure cover or install a lock on

the cabinet.

14. Loop Response Time should be set to 500mS.

Accuracy

This manual has been carefully checked for accuracy. However, C&K

SYSTEMS assumes no liability for inaccuracies or actions resulting

from the use of this manual. In addition, C&K reserves the right to modify

the SYSTEM 238 hardware, software, and manuals without prior

notice.

The following list of options are recommended for a standard SYSTEM

238 installation in a residential environment:

Residential Configuration

1. Program the audible to sound for at least four minutes

before silencing.

2. No zones should be programmed for silent alarm.

3. Fire zones should be programmed for Temporal Code 3

audible alarm.

4. Burglar zones should be programmed for a steady

audible.

5. Burglar loops should be programmed for EOL.

6. Entry Delay should not be greater than 45 seconds.

7. Exit Delay should not be greater than 60 seconds.

8. The Dynamic Battery Test should be enabled.

9. The Unit Status Report should be enabled.

10. The 24-hour Check-in (Test Report) should be enabled.

11. The communicator should not be programmed for Delay

Before Dial.

The following additional options are recommended for commercial

installations.

Mounting

The SYSTEM 238 should be mounted in a location which allows

convenient access to AC power, telephone connections, and earth

ground.

• Remove the circuit board from the cabinet. This will prevent

possible damage to the PCB when removing the knock-outs.

• Remove the knock-outs, as required.

• Mark the screw mounting holes on the wall.

• Mount the cabinet at the desired height and pass the cables

through the knock-outs.

• Replace the circuit board, remembering to connect the ground

lug to the lower left corner of the circuit board.

• Reconnect the spade lug to the lower door hinge. This provides

the earth ground connection for the door.

INSTALLATION

Zone Programming

1. The audible should be programmed to sound at least 15

minutes before silencing.

2. The ring-back function should be activated.

3. The control panel should be mounted in an enclosure that is:

(a) Attack-resistant (C&K Model # 2330-UAC)

(b) Secured with a key-lock and six (6) #6 X 1¼" sheet

metal screws.

removal from mounting surface.

(d) For safe and vault applications the control panel must be

monitored by a UL Listed shock sensor suitable for the

protection of sheet metal enclosures.

4. The Ademco Model AD10-12 bell with Model AB bell housing

should be used.

5. The power and tamper wiring between the bell and the

control panel should be completely enclosed in rigid conduit

or electric metallic tubing for a Grade A system or flexible

conduit for a Grade B system.

6. Zone(s) monitoring tamper circuitry should be 24 hour and

non-shuntable.

FIRE LOOP BURGLAR LOOP

• No Delay Before Dial

• 24-hour arming

• Pulsing audible

• Supervised

- latching for heat

- resetting for smoke

• Not shuntable

• 500mS Loop Response Time

• No Delay Before Dial

• NO/NC with EOL

• Steady audible

• 500mS Loop Response Time

1 2 3 4 5 6 7 ... 27 28

Commenti su questo manuale

Nessun commento

C&K systems System 238 Manuale di Installazione Pagina 2

Commenti su questo manuale

Prodotti e manuali riguardandi Sistemi di controllo di accesso C&K systems System 238